View AWT6521RM48P9_5757158.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

aw t6521 awt6521 multi-band lte/cdma/wcdma/hspa power amplifer data sheet - rev 2.4 22 pin 5 mm x 7 mm x 1 mm surface mount module figure 1: block diagram features ? lte, wcdma/hspa & cdma/evdo applications ? high output power ? +28.5 dbm or more in wcdma (r99) ? +27.5 dbm or more in cdma (rc1) ? high power-added effciency ? 40% in high power mode (wcdma mode) ? low profle 5 mm x 7 mm x 1 mm package ? 2 input ports, 5 output ports, all matched to 50 impedance ? integrated voltage regulator ? built-in directional coupler ? internal dc block on in/out rf ports ? low leakage in shutdown mode ? esd protection on all pins ? rohs-compliant package, msl-3, 260c applications ? lte, wcdma/hspa handsets and data devices operating in umts bands 1, 2, 3, 4, 5, 8 and 25 ? cdma/evdo handsets and data devices operating in band class 0, 1, 6 and 15 high band lo w band c ombiner networ k product description the awt6521 power amplifer module is designed for 3g/4g handsets, smartphones, modems and modules operating in lte, wcdma/hspa and cdma/ evdo modes. the module includes two separate ingap hbt amplifer chains - one to support 850/900 bands, the other for 1700/1900/2100mhz bands. an innovative design allows the module to switch output among as many as 5 different frequency bands. both the input and output rf ports are internally matched to 50 . the awt6521 offers improved effciency and low quiescent current, and includes integrated daisy chained couplers to simplify board design and layout. 02/2012
2 figure 2: pinout (x-ray top view) table 1: pin description pin name description pin name description 1 rf in_hi rf input for 1700/1800/1900 mhz bands 12 rf out_900 rf output for 900 mhz band 2 gnd ground 13 rf out_850 rf output for 850 mhz band 3 v batt battery voltage 14 gnd ground 4 v en_hi enable voltage for high bands 15 v cc supply voltage 5 gnd ground 16 v cc supply voltage 6 v band0 low band select voltage 17 v cc supply voltage 7 v band1 high band select voltage 18 cpl _out coupler output port 8 v mode mode control voltage 19 gnd ground 9 v en_lo enable voltage for low bands 20 rf out_1900 rf output for 1900 mhz band 10 gnd ground 21 rf out_1700 rf output for 1700 mhz band 11 rf in_lo rf input for 850/900 mhz bands 22 rf out_2100 rf output for 2100 mhz band rf ou t_ 2100 rf ou t_ 1700 rf in _h i gn d cp l ou t v bat t gn d 22 21 20 19 18 rf ou t_ 1900 1 2 3 4 5 6 7 8 9 10 11 17 16 15 14 13 12 v cc v cc gn d rf ou t_ 850 v cc v band 0 gn d v mo de v band 1 v en _l o rf in _l o rf ou t _900 v en_hi gn d data sheet - rev 2.4 02/2012 awt6521
3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. parameter min max unit supply voltage (v batt , v cc ) 0 +5 v control voltages (v mode , v band0/1 ) 0 +3.5 v enable voltages (v en_hi , v en_lo ) 0 +3.5 v input rf power (rf in_hi , rf in_lo ) - +10 dbm storage temperature -30 +150 ?c data sheet - rev 2.4 02/2012 awt6521
4 table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operations at 3.1 v or 105 c, p out is derated by 0.6 db. parameter min typ max unit comments operating frequency (f) 824 880 1710 1850 1920 - - - - - 849 915 1785 1915 1980 mhz umts band 5, bc 0 umts band 8 umts band 3 & 4, bc 15 umts band 2 & 25, bc 1 umts band 1, bc 6 supply voltage (v cc ) +0.5 +3.3 +4.35 v supply voltage (v batt ) +2.9 +3.3 +4.35 v control voltages (v mode1 , v band0/1 ) +1.35 0 +1.8 - +3.1 +0.4 v select high state select low state enable voltage (v en_hi , v en_lo ) +1.35 0 +1.8 - +3.1 +0.4 v select high state select low state output power (umts) (1) r99, hpm hspa (mpr = 0), hpm lte (mpr = 0), hpm r99, lpm hspa (mpr = 0), lpm lte (mpr = 0), lpm r99, hpm hspa (mpr = 0), hpm lte (mpr = 0), hpm r99, lpm hspa (mpr = 0), lpm lte (mpr = 0), lpm r99, hpm hspa (mpr = 0), hpm lte (mpr = 0), hpm r99, lpm hspa (mpr = 0), lpm lte (mpr = 0), lpm +27.9 +26.9 +26.4 +15.4 +14.4 +14.4 +28.4 +27.4 +26.9 +15.4 +14.4 +14.4 +28.2 +27.2 +26.4 +15.4 +14.4 +14.4 +28.5 +27.5 +27.0 +16.0 +15.0 +15.0 +29.0 +28.0 +27.5 +16.0 +15.0 +15.0 +28.8 +27.8 +27.0 +16.0 +15.0 +15.0 - - - - - - - - - - - - - - - - - - dbm umts band 1, 3, 4, 5 umts band 1, 3, 4, 5 umts band 1, 3, 4, 5 umts band 1, 3, 4, 5 umts band 1, 3, 4, 5 umts band 1, 3, 4, 5 umts band 2, 25 umts band 2, 25 umts band 2, 25 umts band 2, 25 umts band 2, 25 umts band 2, 25 umts band 8 umts band 8 umts band 8 umts band 8 umts band 8 umts band 8 cdma output power (1) cdma2000 (rc1), hpm cdma2000 (rc1), lpm cdma2000 (rc1), hpm cdma2000 (rc1), lpm cdma2000 (rc1), hpm cdma2000 (rc1), lpm +27.1 +14.4 +26.9 +14.4 +27.5 +14.4 +27.7 +15.0 +27.5 +15.0 +28.1 +15.0 - - - - - - dbm band class 6, 15 band class 0 band class 1 case temperature (t c ) -30 - +105 c data sheet - rev 2.4 02/2012 awt6521
5 table 4: electrical specifcations - band 1 (2100 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = +1.8 v, v band0 = v band1 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v mode gain 25 10 27.5 12.5 31 16 db +28.5 dbm +16 dbm 0 v 1.8 v aclr1 at 5 mhz offset (1) - - -41 -42 -36.5 -37 dbc +28.5 dbm +16 dbm 0 v 1.8 v aclr2 at 10 mhz offset (1) - - -55 <-60 -48 -48 dbc +28.5 dbm +16 dbm 0 v 1.8 v power-added effciency (1) 35 - 40 7 - - % +28.5 dbm +16 dbm 0 v 1.8 v mode control current - <0.06 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.07 0.15 ma through v enable h or l band control current - <0.01 0.06 ma through v band0 and v band1 pins quiescent current - 30 - ma v mode = 1.8 v batt current - 45 - ma through v batt pin, v mode = +1.8 v noise in receive band (2) - - -135 -138 - - dbm/hz p out < +28.25 dbm, v mode = 0 v p out < +16 dbm, v mode = +1.8 v harmonics 2f o 3f o , 4f o - - -42 -50 -30 -35 dbc coupling factor - 27.5 - db input impedance - - 2:1 vswr spurious output level (all spurious outputs) - - -70 dbc p out < 28.5 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range cdma2000 (rc-1) waveform p out v mode adjacent channel power at + 1.25 mhz offset primary channel bw = 1.23 mhz - - -51 -51 -46.5 -47 dbc +27.7 dbm +15 dbm 0 v 1.8 v alternate channel power at + 1.98 mhz offset primary channel bw = 1.23 mhz - - -57 -59 -54 -54 dbc +27.7 dbm +15 dbm 0 v 1.8 v notes: (1) aclr and effciency measured at 1950 mhz. (2) noise measured at 2110 to 2170 mhz. data sheet - rev 2.4 02/2012 awt6521
6 table 5: electrical specifcations - band 1 (2100 mhz) lte operation (rb = 12, start = 0, qpsk) (t c = +25 c, v batt = v cc = +3.3 v, v en = +1.8 v, 50 ? system) notes: (1) aclr and effciency measured at 1950 mhz. parameter min typ max unit comments p out v mode1 gain - - 27 13 - - db +27 dbm +15 dbm 0 v 1.8 v utra aclr1 - - -42 -42 - - dbc +27 dbm +15 dbm 0 v 1.8 v utra aclr2 - - -44 -44 - - dbc +27 dbm +15 dbm 0 v 1.8 v power-added effciency (1) - - 34 8 - - % +27 dbm +15 dbm 0 v 1.8 v spurious output level (all spurious outputs) - - <-70 dbc p out < 27 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.4 02/2012 awt6521
7 table 6: electrical specifcations - band 2 (1900 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = +1.8 v, v band0 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v mode gain 25.5 10.5 28 14.5 31 17 db +29 dbm +16 dbm 0 v 1.8 v aclr1 at 5 mhz offset (1) - - -41 -42 -36.5 -37 dbc +29 dbm +16 dbm 0 v 1.8 v aclr2 at 10 mhz offset (1) - - -53 -60 -48 -48 dbc +29 dbm +16 dbm 0 v 1.8 v power-added effciency (1) 35 - 39 7 - - % +29 dbm +16 dbm 0 v 1.8 v mode control current - <0.06 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.07 0.15 ma through v enable h or l band control current - <0.03 0.1 ma through v band1 pin quiescent current - 30 - ma v mode = 1.8 v batt current - 45 - ma through v batt pin, v mode = +1.8 v noise in receive band (2) - - -135 -138 - - dbm/hz p out < +29 dbm, v mode = 0 v p out < +16 dbm, v mode = +1.8 v harmonics 2f o 3f o , 4f o - - -40 -46 -35 -35 dbc coupling factor - 28 - db input impedance - - 2:1 vswr spurious output level (all spurious outputs) - - -70 dbc p out < 29 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range cdma2000 (rc-1) waveform p out v mode adjacent channel power (1) at + 1.25 mhz offset primary channel bw = 1.23 mhz - - -52 -51 -46.5 -47 dbc +28.1 dbm +15 dbm 0 v 1.8 v alternate channel power (1) at + 1.98 mhz offset primary channel bw = 1.23 mhz - - -56 -59 -54 -54 dbc +28.1 dbm +15 dbm 0 v 1.8 v notes: (1) aclr and effciency measured at 1880 mhz. (2) noise measured at 1930 to 1990 mhz. data sheet - rev 2.4 02/2012 awt6521
8 table 7: electrical specifcations - band 2 & 25 (1900 mhz) lte operation (rb = 12, start = 0, qpsk) (t c = +25 c, v batt = v cc = +3.3 v, v enable = +1.8 v, 50 ? system) notes: (1) aclr and effciency measured at 1880 mhz. parameter min typ max unit comments p out v mode1 gain - - 27.5 14.5 - - db +27.5 dbm +15 dbm 0 v 1.8 v utra aclr1 - - -41 -42 - - dbc +27.5 dbm +15 dbm 0 v 1.8 v utra aclr2 - - -44 -44 - - dbc +27.5 dbm +15 dbm 0 v 1.8 v power-added effciency (1) - - 33 8 - - % +27.5 dbm +15 dbm 0 v 1.8 v spurious output level (all spurious outputs) - - <-70 dbc p out < 27.5 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.4 02/2012 awt6521
9 table 8: electrical specifcations - band 3 & 4 (1700 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band0 = +1.8 v, v band1 = 0 v, v en_lo = 0 v) parameter min typ max unit comments p out v mode gain 24.5 10.5 27 13.5 30 16 db +28.5 dbm +16 dbm 0 v 1.8 v aclr1 at 5 mhz offset (1) - - -42 -43 -36.5 -37 dbc +28.5 dbm +16 dbm 0 v 1.8 v aclr2 at 10 mhz offset (1) - - -55 -60 -48 -48 dbc +28.5 dbm +16 dbm 0 v 1.8 v power-added effciency (1) (without dc/dc converter) 36 - 41 7 - - % +28.5 dbm +16 dbm 0 v 1.8 v mode control current - <0.06 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.07 0.15 ma through v enable h or l band control current - <0.03 0.1 ma through v band0 pin quiescent current - 34 - ma v mode = 1.8 v batt current - 45 - ma through v batt pin, v mode = +1.8 v noise in receive band - - -134 -142 - - dbm/hz 1574.4 - 1576.4 mhz 2110 - 2155 mhz harmonics 2f o 3f o , 4f o - - -42 -55 -30 -35 dbc p out < +28.5 dbm coupling factor - 27.5 - db input impedance - 2:1 - vswr spurious output level (all spurious outputs) - - -70 dbc p out < +28.5 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range cdma2000 (rc-1) waveform p out v mode adjacent channel power (1) at + 1.25 mhz offset primary channel bw = 1.23 mhz - - -52 -51 -46.5 -47 dbc +27.7 dbm +15 dbm 0 v 1.8 v alternate channel power (1) at + 1.98 mhz offset primary channel bw = 1.23 mhz - - -57 -59 -54 -54 dbc +27.7 dbm +15 dbm 0 v 1.8 v notes: (1) aclr and effciency measured at 1747.5 mhz. data sheet - rev 2.4 02/2012 awt6521
10 table 9: electrical specifcations - band 3 & 4 (1700 mhz) lte operation (rb = 12, start = 0, qpsk) (t c = +25 c, v batt = v cc = +3.3 v, v enable = +1.8 v, 0 ? system) notes: (1) aclr and effciency measured at 1747.5 mhz. parameter min typ max unit comments p out v mode1 gain - - 27.5 13.5 - - db +27 dbm +15 dbm 0 v 1.8 v utra aclr1 - - -41 -42 - - dbc +27 dbm +15 dbm 0 v 1.8 v utra aclr2 - - -44 -44 - - dbc +27 dbm +15 dbm 0 v 1.8 v power-added effciency (1) - - 34 8 - - % +27 dbm +15 dbm 0 v 1.8 v spurious output level (all spurious outputs) - - <-70 dbc p out < 27 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.4 02/2012 awt6521
11 table 10: electrical specifcations - band 5 (850 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = 0 v, v band1 = v band0 = +1.8 v, v en_lo = 1.8 v) parameter min typ max unit comments p out v mode gain 25.5 9 28 13 31 16 db +28.5 dbm +16 dbm 0 v 1.8 v aclr1 at 5 mhz offset (1) - - -41 -44 -37 -37 dbc +28.5 dbm +16 dbm 0 v 1.8 v aclr2 at 10 mhz offset (1) - - -57 -60 -48 -48 dbc +28.5 dbm +16 dbm 0 v 1.8 v power-added effciency (1) 35 - 40 8 - - % +28.5 dbm +16 dbm 0 v 1.8 v mode control current - <0.06 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.07 0.15 ma through v enable h or l band control current - <0.03 0.1 ma through v band0 or v band1 pins quiescent current - 32 - ma v mode = 1.8 v batt current - 21 - ma through v batt pin, v mode = +1.8 v noise in receive band (2) - - -136 -138 - - dbm/hz p out < +28.5 dbm, v mode = 0 v p out < +16 dbm, v mode = +1.8 v harmonics 2f o 3f o , 4f o - - -44 -50 -35 -35 dbc p out < +28.5 dbm coupling factor - 26.5 - db input impedance - - 2:1 vswr spurious output level (all spurious outputs) - - -70 dbc p out < +28.5 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range cdma2000 (rc-1) waveform p out v mode adjacent channel power (1) at + 1.25 mhz offset primary channel bw = 1.23 mhz - - -51 -51 -46.5 -47 dbc +27.5 dbm +15 dbm 0 v 1.8 v alternate channel power (1) at + 1.98 mhz offset primary channel bw = 1.23 mhz - - -60 -63 -57 -57 dbc +27.5 dbm +15 dbm 0 v 1.8 v notes: (1) aclr and effciency measured at 836.5 mhz. (2) noise measured at 869 to 894 mhz. data sheet - rev 2.4 02/2012 awt6521
12 notes: (1) aclr and effciency measured at 836.5 mhz. able 11: electrical ecifcations and 5 (850 mhz) le eration (mpr 0 d aeform r 12 10 mhz p) (t c = +25 ?c, v batt = v cc = +3.3 v, v enable ? system) parameter min typ max unit comments p out v mode1 gain - - 27 11 - - db +27 dbm +15 dbm 0 v 1.8 v utra aclr1 - - -41 -42 - - dbc +27 dbm +15 dbm 0 v 1.8 v utra aclr2 - - -45 -46 - - dbc +27 dbm +15 dbm 0 v 1.8 v power-added effciency (1) - - 34 8 - - % +27 dbm +15 dbm 0 v 1.8 v spurious output level (all spurious outputs) - - -70 dbc p out < 27 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.4 02/2012 awt6521
13 table 12: electrical specifcations - band 8 (900 mhz) wcdma operation (r99 waveform) (+25 c, v batt = v cc = +3.3 v, v en_hi = v band1 = v band0 = 0 v, v en_lo = 1.8 v) parameter min typ max unit comments p out v mode gain 25.5 8.5 27.5 11 31 15 db +28.8 dbm +16 dbm 0 v 1.8 v aclr1 at 5 mhz offset (1) - - -42 -43 -37 -37 dbc +28.8 dbm +16 dbm 0 v 1.8 v aclr2 at 10 mhz offset (1) - - -56 -60 -48 -48 dbc +28.8 dbm +16 dbm 0 v 1.8 v power-added effciency (1) 35 - 40 8 - - % +28.8 dbm +16 dbm 0 v 1.8 v mode control current - <0.06 0.12 ma through v mode pin, v mode = +1.8 v enable current - <0.07 0.15 ma through v enable h or l band control current - <0.03 0.1 ma through v band0 or v band1 pins quiescent current - 33 - ma v mode = 1.8 v batt current - 23 - ma through v batt pin, v mode = +1.8 v noise in receive band (2) - - -136 -137 - - dbm/hz p out = +28.8 dbm, v mode = 0 v p out = +16 dbm, v mode = +1.8 v harmonics 2f o 3f o , 4f o - - -42 -50 -30 -35 dbc p out < +28.8 dbm coupling factor - 27.0 - db leakage current (total) - <6 12 a v batt = +4.5 v, v cc = +4.5 v, shutdown mode (all v batt & v cc pins) input impedance - - 2:1 vswr spurious output level (all spurious outputs) - - -70 dbc p out < +28.8 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range notes: (1) aclr and effciency measured at 897.5 mhz. (2) noise measured at 925 to 960 mhz. data sheet - rev 2.4 02/2012 awt6521
14 notes: (1) aclr and effciency measured at 897.5 mhz. able 13: electrical ecifcations and 8 (900 mhz) le eration (mpr 0 d aeform r 12 10 mhz p) (t c = +25 ?c, v batt = v cc = +3.3 v, v enable ? system) parameter min typ max unit comments p out v mode1 gain - - 27.5 11 - - db +27 dbm +15 dbm 0 v 1.8 v utra aclr1 - - -41 -42 - - dbc +27 dbm +15 dbm 0 v 1.8 v utra aclr2 - - -45 -46 - - dbc +27 dbm +15 dbm 0 v 1.8 v power-added effciency (1) - - 34 8 - - % +27 dbm +15 dbm 0 v 1.8 v spurious output level (all spurious outputs) - - -70 dbc p out < 27 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating ranges load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.4 02/2012 awt6521
15 table 14: logic interface specifcations figure 3 : evaluation board schematic logic programming application information mode of operation v en_hi v en_lo v band0 v band1 v mode umts band 1, cdma bc 6 high low low low x umts band 2 & 25, cdma bc 1 high low low high x umts band 3 & 4, cdma bc 15 high low high low x umts band 5, cdma bc 0 low high high high x umts band 8 low high low low x standby mode low low x x x shutdown mode low low low low x high power mode (hpm) x x x x low low power mode (lpm) x x x x high rf ou t_ 2100 rf ou t_ 1700 rf in _h i gn d cp l ou t gn d v batt gn d 22 21 20 19 18 g nd sl ug v en _h i rf ou t_ 1900 1 2 3 4 5 6 7 8 9 10 11 17 16 15 14 13 12 v cc v cc gn d rf ou t_ 850 v cc v band 0 gn d v mo de v band 1 v en _l o rf in _l o rf ou t_ 900 68p f c2 2.2u f c2 .1 u f c3 68p f c1 bat t bat t data sheet - rev 2.4 02/2012 awt6521
16 figure 5: branding specifcation figure 4: package outline - 22 pin 5 mm x 7 mm x 1 mm surface mount module package outline aw t6521r lllllnn yy wwc c anadigics logo pin 1 identifier pa rt number date co de y y= y ear ww= wo rk w eek l ot number c ountr y co de (c c) data sheet - rev 2.4 02/2012 awt6521
17 figure 6: recommended pcb layout information pcb and stencil design guideline data sheet - rev 2.4 02/2012 awt6521
18 notes: (1) material: 3000 (carbon filled polycarbonate) 100% recyclable. figure 7: carrier tape figure 8: reel data sheet - rev 2.4 02/2012 awt6521
19 ordering information order number temperature range package description component packaging awt6521rm48p8 -30 4c to + 105 4c r o hs compliant 22 pin 5 mm x 7 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel AWT6521RM48P9 -30 4c to + 105 4c r o hs compliant 22 pin 5 mm x 7 mm x 1 mm surface mount module partial tape and reel warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. import ant notice anadigics 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.4 02/2012 awt6521

▲Up To Search▲

Price & Availability of AWT6521RM48P9

	To Download AWT6521RM48P9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .